You can login here to track the status of your ticket.PLEASE NOTE:
Your login credentials are not the same as the 888VoIP Product Portal, you must register first before using the Ticket Tracking feature.
How to use the TFTP Recovery Mode on Yealink Devices
Posted by Nick Schrantz, Last modified by Nick Schrantz on 12 April 2016 04:08 PM
Overview: Also known as a Recovery Mode Update, the TFTP process can be used to save what can be seen as an otherwise dead phone. This process is most useful in the scenario that a phone either gets stuck in a boot loop, or stays on a Welcome Initializing...Please Wait screen. However, it can also be useful on a device where a factory reset does not seem to be resetting the device correctly. If you find that your device fits into any of these categories, the TFTP recovery can be performed; it will reflash the firmware on the device in the case of a corrupt firmware and if successful, will allow your device to fully boot again.
Set-up Guide: In order to proceed with this process and be able to successfully perform the TFTP recovery, you are going to need:
Step 1: Gathering the Necessary Files
You will be able to find all of the files necessary for the recovery of your device on our shared google drive.
From here, you can navigate to the folder for the device that you will be trying to recover, inside of that folder you will find all of the files necessary to perform the TFTP recovery on that device. Download these files and place them in a folder that you will have easy access to. Make sure that you have downloaded all the files in your devices folder, the process will not be successful if you have not acquired all of the files necessary for your device.
Step 2: Setting Up Your TFTP Server
The process to setup your TFTP server is not overly difficult. Once downloaded from the link above, allow PumpKIN to install and then open it once it is installed. You will see a screen as below.
Now, you are going to want to hit the options button and you will be presented with a screen as shown below.
On this screen, you are going to want to set the TFTP filesystem root to the folder that you downloaded the files from above in, in this examples case, they are located in a TFTP folder that is on my desktop. You will also want to ensure that you change the read request behavior to give all files and the write request behavior to take all files, so that way the TFTP program will know to allow the phone to request all of the files it is looking for in that folder. Once this is done you can click OK to save your changes and you are ready to move on to the next step.
Step 3: TFTP Recovery
Depending upon what device you are going to be recovering, this process will deviate slightly.
Step 1: With your device off, press and hold down on the speakerphone button. While holding this button down, either plug in the power adapter or reinsert your PoE cable. Keep holding this button down until you are presented with a screen as shown below.
***Please Note*** The CP860 follows a slightly different process, instead of holding down the speakerphone button during this process, you will be holding down the second soft key button from the left as there is no speakerphone button to hold down on the CP860. This is circled in the picture below.
Step 2: On this screen you will see 4 options, IP Addr:, NetMask:, GateWay:, and TFTP IP: as pictured below. For the IP Addr:, you are going to want to insert an unused IP address that is available on your network, in our example we are using 192.168.90.236. Next, for the NetMask:, you are going to want to insert the subnet mask that your network is operating under, in our example we are using 255.255.255.0. However, this can be different depending upon your network configuration. Next, for the GateWay:, you are going to want to insert the IP address that your router is located at, in our example that would be 192.168.90.1. Finally, you are going to want to insert the IP address of your PC that is hosting PumpKIN for the TFTP IP:. Our TFTP server is located on a PC at IP 192.168.90.3 so we inserted that value for our TFTP IP:. Now, in the case that you are not aware of your network details, please contact your network administrator and they can help you get that information. Once you have filled these details out, press the OK key on the phone and it will start requesting the files that you downloaded from earlier.
Step 3: The process can take several minutes to complete and during that time you will see a ...Updating...Please Wait displayed on the screen. Allow it to complete it's process, and the phone will reboot once it is complete. If it was a successful flash, you will be presented with a factory reset device that has been recovered. If you are presented with an Update Fail... screen you will want to ensure that the details that you entered on the phone are correct and that you have pointed PumpKIN at the correct folder. Also, please ensure that you have downloaded the correct files and all of the files necessary for your device.
Step 1: The process to recover a W52P base unit is slightly different when compared to recovering a phone. First, you will need to get the IP address information on your PC that will be hosting PumpKIN as configured below, these are the default values that the W52P will look for when put into recovery mode.
Step 2: During this process the base unit will get an IP address of 192.168.0.100 and will look to the IP address as configured above for its recovery files. While the unit is off, long press the button on the front of the device, it looks like a small dot with three waves eminating out from the center. While continuing to hold this button reconnect your power adapter or PoE cable. Continue holding until you see the three lights on the base unit turn on one by one (power led --> network led --> phone led)
Step 3: This process can take several minutes to complete, however once sucessful the unit will reboot and once you have solid lights on the front of the device you will be able to access the device at the IP address that it has received from DHCP.
Once the steps above have been completed sucessfully, your device will have rebooted and you will have sucessfully recovered your device.